|
| |
Product Classification : Can Making
|
|
CanNeed-DER-4 Digital Enamel Rater
|
|
The CanNeed-DER-4Digital Enamel Rater is able to detect the exposed metal position more easily compare to the former models. The reformative electronic design makes it more sensitive, reliable and accurate. The anticorrosion characteristic of the enhanced can body support is ensured its durability. The film coated buttons are more durable and with better corrosion resistance.
CanNeed-DER-4 is the industry standard. The new CanNeed-DER-4Enamel Rater instrument test the coverage of the enamel coating inside food and beverage cans, aerosol-cans and also different kinds of ends. It displays an index of the amount of metal exposed by incomplete enamel coverage on a clear, easily read digital LED.
|
|
|
ALT-600 Leak Tester for Aerosol can
|
|
The “Canneed ALT-600 / ALT-800 Leak Tester for Aerosol can” is used for testing the leakage of Aerosol cans. ALT-600 can test 6 cans at the same time, and ALT-800 can test 8. The permeability tester for aerosol cans blows up the cans up to a maximum of 10 bar and submerges them under water. At the leaking spots of the can then visible air-bubbles escape.
A special clamping system enables to measure different diameters and heights with one device. Two pressure levels can be set with the tester. The first is meant to hold and seal the can, the second step sets in when the mount with the cans has reached the lowest position. The maximum test pressure is 10 bar.
|
|
|
BMS-1000 Automatic Can Measure System for Back End
|
|
The CanNeed "BMS-1000 Automatic Can Measure System For Back End" is used to measure Flange Width, Can Height & Internal Diameter of 2-pc can. It’s designed by practical experience and applied to back end inspection. It can be adjusted rapidly and applicable for various can height.
|
|
|
CanNeed-CAN-10774 Planer and Shaper Pin Height Gauge
|
|
CanNeed-CAN-10774 The Pin Height Gauge is commonly used in the initial setup of the seamer to ensure double seaming
performance and air removal.
All working surfaces are hardened and accurately ground.
|
|
|
CanNeed-STR-100 Seam Stripper
|
|
The CanNeed-STR-100 Can Cover Trim Stripper is designed to quickly and accurately cut can cover trim in place for inspection of cover hook wrinkles and tightness. The CanNeed-STR-100 is also used for boiling tests where a large number of sample cans need to be cut away from the lid to observe the inside of the can.
|
|
|
CanNeed-SM-24 Electric Belt Drive Seamer
|
|
The Canneed "SM- 24 Electric Belt Drive Seamer" (Desktop model) enables the users to do more lab tests. Such as, adjusting some technique, enhancing the products quality, test the empty cans and free ends, to insert a temperature logger into a can before running a temperature monitoring.
|
|
|
CanNeed-ALT-100 Leak Tester for Aerosol can
|
|
CanNeed-ALT-100 Leak Tester for Aerosol can is used for testing the leakage of Aerosol cans in a water bath. The can is freely suspended and submerged into the water. At the same time it is subjected to pressure and leaks are revealed by air bubbles. Test pressure 8 - 10 bar. The test procedure is performed semi-automatically. The tester is suitable for all aerosol can diameters. The maximum can height is 300 mm.
|
|
|
SCG-200 Seamer clearance Gauge
|
|
The CanNeed SCG-200 Seamer clearance Gauge, a quick and accurate way to set up seamers.
To measure the roll height off the chuck and the lateral distance between the roll and chuck.
|
|
|
CanNeed-WTG-200 Wall Thickness Gauge
|
|
The CanNeed-WTG-200 Wall Thickness Gauge measures the Top wall and Middle wall Thickness for Trimmed 2-Piece Cans. Available for any Trimmed 2-Piece Cans of any height (Please indicate the can height when ordering).
Configure with Mitutoyo Standard SPC Data Output and the resolution can reach 0.001mm.
If purchase the adapter and cable, the gauge can be connected to a computer or SPC system for data collection.
|
|
|
CanNeed-IDG-100/200/300 Can Internal Diameter Gauge
|
The “CanNeed-IDG-100 Internal Diameter of Can” is used to measure the internal diameter of small cans, such as 200, 202, 206, 209.
The “CanNeed-IDG-200 Internal Diameter of Can” is used to measure the internal diameter of larger cans. According to clients’ request, CanNeed-IDG-200 can be made to measure 2 to 3 different sizes of cans at the most at the same time. Note: The difference between the internal diameters of the two cans must be over 10mm.
When placing the order, please indicate the internal diameters of the cans, such as 202 neck-in cans, 206 neck-in cans.
With the Mitutoyo 0.01mm resolution digital indicator.
If purchased the adapter and cable, the gauge can be connected to a computer or SPC system for data collection.
|
|
|
CSM-208, CSM-207 Can Seam Micrometers (Fine tuning)
|
The CanNeed CSM series Can Seam Micrometers are use for measuring the seam thickness and length. The fine tuning function helps to avoid the deviation caused by over rotation.
CSM-208 is applicable to measure the seam thickness and length of flat bottom straight wall cans.
CSM-207 is applicable to measure the seam thickness and length of aerosol cans and necked-in cans.
|
|
|
CanNeed-CSS-300 Seam Saw
|
|
CanNeed-CSS-300 Seam saw is a special seam circular saw with double cut for double seam inspections.
The CanNeed -CSS-300 has specially designed for the irregular shaped cans, like rectangle cans, oval cans, etc. Also aerosol-cans can also be sawed with the saw. The nitrated blades achieve together with the speed of approx. 1.000 r/min. so that comes a very plain cut surface. The seam Image on the CanNeed series of Automatic Seam Monitors gets thereby very clear and improves measurement speed and reliability.
|
|
|
CAN-1050 Can Closing Force Gages
|
|
The CanNeed CAN-1050 Can Closing Force Gages can lower scrap rates and set up time. you can quickly and easily job-set multiple-station canning machines. These Gauges come with and adjustable self-loading micrometer dial, calibrated in thousandths. This means you may accurately deflect spring-loaded can wear plates to any desired dimension.
|
|
|
CanNeed-CAN-1050D Digital Can Closing Force Gauge
|
|
CanNeed-CAN-1050D Can Closing Force Gauge is for measuring the force of seaming head of the seaming machine. By using CanNeed-CAN-1050d, producers can avoid product defects caused by over plating: sharp edge, seam breakage, body deformation, body hook overlength, over large countersink and so on. In the meantime, producers can also avoid product defects caused by too small pallet lift force: slippery cans, too short hook and so on.
|
|
|
EBT-300 Buckle Tester for Loose Ends(with Missile Test)
|
|
The CanNeed "EBT-300 Buckle Tester for loose ends" is for testing the exact pressure at which the end buckles. Any end of varying diameter may be tested: change parts are available that can be exchanged within seconds. Three testing mode, "Buckle Test", "Missile Test", and "Score Burst Test".
|
|
|
CanNeed-CMD-200S Can Measure Desk for Rear Stations
|
The CanNeed CMD-200 Can Measure Desk for Rear Stations is developed on basis of the long experience of Rear stations in 2 -piece can product line.
CMD-200 Measures the Flange width, can height, inner Diameter. Please indicate the can type when ordering.
|
|
|
CanNeed-CAN-10774 Planer and Shaper Pin Height Gauge
|
|
CanNeed-CAN-10774 The Pin Height Gauge is commonly used in the initial setup of the seamer to ensure double seaming
performance and air removal.
All working surfaces are hardened and accurately ground.
|
|
|
CanNeed-CND-TRK-300 Oven Temperature Tracker
|
|
The “CanNeed-TRK-300 Oven Temperature Tracker” is a professional oven temperature curve inspection system for the coating industry, it is including the data logger, heat insulation case, software (Chinese / English) and thermocouples.
"CanNeed-TRK-300 Oven Temperature Tracker” is use to pass through the oven with the solidifying products, and record down the real temperature during the process. The logger is in the centre of the system. Heat insulation case is for protecting the logger from over heat by the oven. When passing through the oven, the CanNeed-TRK-300 Oven Temperature Tracker will record down the real time temperature of the solidifying products through the 5 thermocouples which were connected to the products, and one thermocouple is for recording the air temperature of the oven. After the recording process was finished, use the CND_TRK Software to analyze the temperature data and generate the detail reports.
|
|
|
PNR-E100 Pressure No Return Tester for Ends
|
|
The CanNeed "PNR-E100 Pressure No Return Tester for Ends" can measure the PNR value (Plastic Deformation) and the buckle value of the ends. During the whole pressurization process, use the micrometer to track and measure the deformation amount, generate the curve through the software and analyze the correlation between pressure and deformation amount of the ends.
|
|
|
CanNeed SeamSight®-V3 Full Automatic Seam Monitor
|
|
The CanNeed Seam Sight® professional seam measuring software will do the line positioning automatically and the measurement to be finished within 1 second! The software also adopted the data base management system, all the measurement data will be restored in the system data base, so that to enhance the software performance and more convenience in data management. The result statistic and result chart has been added in the data base screen for overview and comparison. Meanwhile, the measurement screen has been optimized for a vivid result display.
The CanNeed Seam Sight® Full Automatic Seam Monitor has adopted the advanced optical system and Golden Lens® video capture device, which interference-free of external light source and ensured the high image definition and the measurement accuracy. The Seam Sight® system is equipped with the new seam measuring software Seam Sight® .
|
|
|
CanNeed-CSG-200 Countersink Gauge (Digital)
|
|
The CanNeed-CSG-200 Countersink Gauge (digital) is a Digital gauge for measuring Countersink depth parameters (the depth of beader of can). With the Mitutoyo 0.01mm Resolution Digital Indicator.
The gauge can be connected to a computer or SPC system via the adapter and cable, so that to avoid the manual recording and personal error. The gauge can also combine with Canneed Seam Monitors and import the measurement data into computer.
|
|
|
BDG-100 Bottom Depth Gauge
|
|
The CanNeed "BDG-100 Bottom Depth Gauge" is a Digital gauges for measuring Bottom depth parameters of beverage cans. Please indicate the can diameter when ordering.
|
|
|
CanNeed-SM-24 Electric Belt Drive Seamer
|
The Canneed “SM- 24 Electric Belt Drive Seamer” (Desktop model) enables the users to do more lab tests. Such as, adjusting some technique, enhancing the products quality, test the empty cans and free ends, to insert a temperature logger into a can before running a temperature monitoring.
It is much more convenient for those lab tests, fast, easy and high efficiency.
|
|
|
FWG-100-D, FWG-200-D, FWG-300-D Flange Width Gauge
|
|
The “CanNeed-FWG-100-d, CanNeed-FWG-200-d, CanNeed-FWG-300-d Flange Width Gauge (digital)” is used to measure the flange width of empty cans. Reliable design, invariableness measuring pressure and measuring angle which enable the inexperienced operators can also perform the measurement accurately. Auto aligning the center of can body, applicable for different types of cans.
If purchased the adapter and cable, the gauges can be connected to a computer or SPC system for data collection, avoiding the manual recording and personal error.
|
|
|
RPG-100 Roll profile Gauge
|
|
The CanNeed RPG-100 is able to scan profiles of seaming Rolls and Chucks (or other tooling - including carbide and ceramic tools) easily and quickly. The system can be used for acceptance testing for new seaming rolls or chucks, for quality assurance purposes and for stress analysis. Monitor tooling wear to replace rolls and chucks only when they need to be replaced
|
|
|
CEBT-100 Buckle Tester for Can and End
|
The “Canneed CEBT-100 Buckle Tester for Can and end” determines the exact pressure at which the Can and End begins to buckle. With 4 measuring mode:
|
|
|
CanNeed-IDG-100/200/300 Can Internal Diameter Gauge
|
The “CanNeed-IDG-100 Internal Diameter of Can” is used to measure the internal diameter of small cans, such as 200, 202, 206, 209.
The “CanNeed-IDG-200 Internal Diameter of Can” is used to measure the internal diameter of larger cans. According to clients’ request, CanNeed-IDG-200 can be made to measure 2 to 3 different sizes of cans at the most at the same time. Note: The difference between the internal diameters of the two cans must be over 10mm.
When placing the order, please indicate the internal diameters of the cans, such as 202 neck-in cans, 206 neck-in cans.
With the Mitutoyo 0.01mm resolution digital indicator.
If purchased the adapter and cable, the gauge can be connected to a computer or SPC system for data collection.
|
|
|
ELT-100 Leak Tester for End
|
The "Canneed model ELT-100 Leak Tester for End "is used to determine the pressure at which ends buckle. This tester is also used to test for pin hole leaks in the tab score and rivet area.
The ELT-100 applies high pressure air to the product side of and end until the end fails. Leaking spots are made visible by revealing bubbles in the water bath. The failure of an end occurs either when the end buckles or when it starts leaking, leakage is generally caused by faulty scores or rivets.
|
|
|
CanNeed-AMG-300 Aerosol Measuring Gauge
|
|
The CanNeed AMG-300 Aerosol Measuring Gauge is a Convenient Gauge for Aerosol Cans, it can measures 6 characteristics in 1 compact Gauge. measures the following characteristics:
1) Can Height over all (E)
2) Can Height over the seams (D)
3) Can height between the seams (F)
4) Top Outside Diameter (K),
5) Top seam Outside Diameter
6) Bottom seam Outside Diameter
The CanNeed AMG-300 saves valuable time and table space. Combine five essential aerosol can gauges into one convenient measurement Gauge.
|
|
|
CanNeed-STR-100A Seam Stripper
|
The automatic “CanNeed-STR-100 Seam Stripper” is a sensible, affordable, teardown method to prepare the double seam teardown analysis. One fast, safe teardown operation without damaging or distorting the cover hook. Reduce teardown time for more frequent inspections. Tooling quick change in few seconds. Models are available for most common can sizes of beverage and food cans. When ordering, the end diameter and can height must be specified so that the appropriate change parts are included. Efficient cut and strip both aluminium and steel cans in a single motion. 10 seconds per can. Eliminates the repetitious actions by hand.
An important part of any seam evaluation is the actual teardown of the can seam to determine tightness or wrinkled rating.
|
|
"If you can not find the product you need, please contact us or leave a message."
|
|
