|
| |
Product Classification : All Products
|
|
CanNeed-ELT-100 Leak Tester for End
|
|
The “CanNeed-ELT 100 Leak Tester for End” is used to determine the pressure at which ends buckle. This tester is also used to test for pin hole leaks in the tab score and rivet area.
There are two intended testing purpose for CanNeed-ELT-100 Leak Tester for End:
1. To determine the pressure at which ends buckle
2. To test for pin hole leaks in the tab score and rivet area
|
|
|
CanNeed-PTG-100 Digital Plate Thickness Gauge
|
This unit serves for quickly checking the thickness of plates. The sample is presented vertically in this version. Equipped with the Mitutoyo 0.001mm Resolution Digital Indicator.
If purchased the adapter and cable, the gauge can be connected to a computer or SPC system for data collection.
|
|
|
CanNeed-EBT-400 Buckle Tester for Loose Ends (With Missile Test)
|
|
The CanNeed-EBT-400 Buckle Tester for Loose ends is for testing the exact pressure at which the end buckles. Any end of varying diameter may be tested: change parts are available that can be exchanged within seconds. Three testing modes: “Buckle Test”, “Missile Test”, and “Score Burst Test”.
|
|
|
CanNeed-PNR-E200 Pressure No Return Tester for Ends
|
|
The CanNeed-PNR-E200 Pressure No Return Tester for Ends can measure the PNR value (Plastic Deformation) and the buckle value of the ends. During the whole pressurization process, use the micrometer to track and measure the deformation amount, generate the curve through the software and analyze the correlation between pressure and deformation amount of the ends.
|
|
|
CanNeed-HDY Crown Height & Thickness Tester
|
The “CanNeed-HDY Crown Height & Thickness Tester” has fine designed testing base, the crown height and thickness are measured by the dial indicator.
The CanNeed-HDY has widely used in crown factories, beer and beverage factories.
The CanNeed-HDY is made of stainless steel.
|
|
|
CanNeed-EMD-400 End Measure Desk
|
|
CanNeed-EMD-400 End Measure Desk is developed according to the long-term practical experience, it can be used next to the production line or in the laboratory.
The CanNeed-EMD-400 measures the End Curl Height, End Curl Diameter, End Curl Width and Countersink.
|
|
|
CanNeed-ATCT-1000 Automatic Tensile and Compression Tester
|
|
|
|
|
CanNeed-AVM-320
|
|
|
|
|
CNV-80
|
|
|
|
|
CanNeed-SPC SPC SoftWare
|
|
|
|
|
CND-SST-3 Secure Seal Tester
|
|
The "CND-SST-3 Secure Seal Tester" is used to test seal integrity on the glass or plastic containers and cans. The SST-2 has been designed to address the special needs of sealing cans and bottles that use aluminum roll-on, twist crowns, or plastic caps. The SST-2 operates with compressed air, nitrogen, or carbon dioxide. By detecting gas leakage, rather than liquid, the Secure Seal Tester gives more sensitive, accurate readings.
SST-3 is constructed from anodized aluminum, stainless steel, and plastic materials. The tester's rugged construction withstands production line abuse, yet is accurate enough for laboratory use.
|
|
|
SeamSight®-B Full Automatic Seam System
|
|
The CanNeed Seam Sight® Full Automatic Seam Monitor has adopted the advanced optical system and Golden Lens® video capture device, which interference-free of external light source and ensured the high image definition and the measurement accuracy. The Seam Sight® system is equipped with the new seam measuring software Seam Sight®.
The CanNeed Seam Sight® -A system can automatically collect the data from STG-200-D Seam Thickness Gauge and CSG-200 Countersink Gauge. The actual seam thickness and countersink can be generated reports together with other data. To optimize the measurement process.
Measurement Process
Before cutting the sample can, use STG-200-D Seam Thickness Gauge to measure the seam thickness rate; meanwhile, use CSG-200 Countersink Gauge to measure the countersink rate; then the Seam Sight -A will collect the both data automatically.
After that, the sample can should be cut with CSS-1000 Anti-noise Seam Saw or CSS-2000 Seam Saw and placed at the camera position of the monitor. Then, the seaming images will be displayed on the screen. The auto measurement will be finished within 1 second if you press the “Confirmation” button. All images and measurement data will be saved in the system data base.
|
|
|
PEBT-4000 PET Bottle Pressure Tester (Burst Tester)
|
|
Canneed “PEBT-4000 PET Bottle Pressure Tester (Burst Tester)” is an advance testing equipment specialized for testing the PET bottles. It has been designed in conformity to the three (3) international commonly used testing methods, users can select the testing mode according to their requirement. PEBT-4000 is able to test the pressure capabilities that under a preset pressure or the burst test.
By the means of water replenishing pressurization, the pressurizing process was linearized, and to increase until reaching the preset point or burst point.
Users can select the testing mode through the touch-screen. Fill the sample, close the protection door, then press start. When the testing starts, the PEBT-4000 will clamp the sample and run accord with the settings automatically. The touch-screen will display the real-time pressure value and record down the max. pressure (passing test) and burst pressure (destructive test).
|
|
|
CN-HC-100
|
|
|
|
|
CN-XR-100
|
|
|
|
|
CanNeed-CTSA-100 Carton Tilt Sliding Angle Tester
|
|
CanNeed-CTSA-100 Carton Tilt Sliding Angle Tester is mainly used for testing the friction performance of corrugated cartons or other packaging products when they are sliding. When the boxes are stacking and transporting, if the surface friction coefficient is too small, it is easy to cause slip. With the help of CTSA-100 test, users can improve the sliding resistance of packaging. The CanNeed-CTSA-100 is developed and manufactured according to the international standard of DIN 53119-2-1997.
|
|
|
CanNeed-CRT-100 Crush Resistance Tester
|
|
CanNeed-CRT-100 Crush Resistance Tester is designed and used for testing corrugated board and paper, applies to Ring Crush Test (RCT), Edge Crush Test (ECT), Flat Crush Test (FCT), Peel Adhesive Test (PAT) , as well as Corrugating Medium Test (CMT) & Corrugated Crush Test (CCT) for corrugated paper diameter smaller than 60mm, which meets to the International Inspection Standards of GB/T 2679.8, GB/T 6546, GB/T 6548, etc.
CanNeed-CRT-100 has the functions of testing, converting, adjusting, memorizing, querying historical data, data printing and other functions included in the standard configuration, and has powerful data processing functions.
|
|
|
CanNeed-CAT-10 Cobb Absorption Tester
|
|
CanNeed-CAT-10 Cobb Absorption Tester is designed to evaluate the water absorption rate of paper, thought testing the water absorbance of the materials when subjected to moist condition. It is suitable for sizing paper and water absorption on cardboard surface, not suitable for basis paper and embossed paper with basis weight less than 50g / m2, low sizing degree or more pinholes.It is designed and manufactured according to the national standard of GB/T 1540-2002, “Paper and board-Determination of water absorption-Cobb method”.
|
|
|
CanNeed-ATCT-1000 Automatic Tensile and Compression Tester
|
|
CanNeed-ATCT-1000 Automatic Tensile and Compression Tester is applicable for detecting the tensile stress and strength, breaking elongation, peel strength, 90° tear force, heat-sealing strength, adhesive strength, puncturing resistance force, low-speed unwrapping force and opening force on the samples involved of plastic film, laminated films, flexible packaging materials, adhesives and adhesive tapes, self-adhesive, rubber, paper and aluminum-plastic panel, etc. It’s developed and manufactured in terms of GBT16825-2022 and other standards.
|
|
|
CanNeed-BPT-4000 Ramp Pressure Tester
|
BPT-4000 Ramp Pressure Tester is an advanced testing instrument for pressure testing glass containers,also can be used to test the burst value.
Two positions,high efficiency.PLC controlled,LCD touch screen display.Automatic clamping system,servo control pressure process.Display real-time data,test and save data automatically.
Two test ways: :linear pressurization and pressure maintaining.Users can choose testing way as to actual demands.
|
|
|
CAN-85B, CAN-125B Pasteurization Temperature Monitor (PU Monitor)
|
CanNeed CAN-85B, CAN-125B Pasteurization Temperature Monitor (PU Monitor), is the most advanced PU Monitor, high quality and powerful function.
Convenience and durable
The logger of CAN-85B, CAN-125B PU Monitor is portable and it was a stainless steel weldless one-piece design, which ensured its excellent sealability and long service life.
Powerful function
CAN-85B, CAN-125B PU Monitor record and store the temperature data of the whole sterilizing process, calculate the total PU value, max. temperature. The powerful professional software CND-LogSee can print the report and curve, save data .
|
|
|
CanNeed-PBT-100 Paper Board Bursting Strength Tester
|
|
CanNeed-PBT-100 Paper Board Bursting Strength Tester is used for testing and analyzing the bursting strength of cardboard, carton and other paper materials. It’s suitable for all kinds of paperboard (including corrugated board and cardboard) with a burst resistance of 350Kpa-5500Kpa.The tester is designed in line with the International Inspection Standard “GBT1539-2007 Cardboard Breaking Resistance Determination”.
|
|
|
CanNeed-SPC SPC SoftWare
|
|
|
|
|
X-Chip-A330
|
|
|
|
|
X-Chip-200
|
|
|
|
|
Seam-X-Line X-Ray Automatic Seam Scanner (Non-destructive)
|
|
Seam-X®-Line Automatic Seam Scanner adopts non-destructive measurement method to measure the seam quality, suitable for measuring the aluminium cans, steel cans , aluminium-iron composite cans and etc. If configured with the conveyor, it can achieve automatic sampling from the production line. It's applicable for laboratory or producing department.
|
|
|
|
Seam-X-Line X-Ray Automatic Seam Scanner (Non-destructive)
|
|
Seam-X®-Line Automatic Seam Scanner adopts non-destructive measurement method to measure the seam quality, suitable for measuring the aluminium cans, steel cans , aluminium-iron composite cans and etc. If configured with the conveyor, it can achieve automatic sampling from the production line. It's applicable for laboratory or producing department.
|
|
|
CMT-200 Mobility/ Lubricity Tester for Cans
|
|
The CanNeed “CMT-200 Mobility / Lubricity Tester for Cans” is for measuring the coefficient of sliding friction of can body and bottom. It can also measure the coefficient of sliding friction of blanks.
Install the corresponding clamp and place the sample on the clamp, then put the bob-weight unit on the sample. Pull the bob-weight and the indicator will display the coefficient of sliding friction.
|
|
|
CLX-50
|
|
|
|
|
CL-100
|
|
|
|
"If you can not find the product you need, please contact us or leave a message."
|
|
